TapPro is a software for developing taps for professionals. This software calculates the complete cutting geometries for taps. It gives all the setup information needed to make high quality taps. The unimaginable is that TapPro also specifies the relief in the thread and the relief in the chamfer as well as the taper angle in the thread and a lot more. This  for 6,500 different taps geometries, this for soft steels, universal steels, stainless steels, high strength steels, short chipping steels, titan alloy steels, aeronautical steels and fine grain steels.

» Develop blanks according to the norm including the requested tolerances
» Develop a full geometry with a little basic knowledge of taps
» Recall needed information to develop new taps according to the material group as:
XXX» cutting angle value
XXX» tread relief angle value
XXX» back tape angle value
» Recall all technical information to develop flutes
» Testing your development of new taps with help of TapPro
» Recall all information to create a professional development of new taps
» Optimizing your development of new taps with the troubleshooting module
» Learning more about taps with the knowhow module
» Finding all necessary formula to understand how TapPro calculates the development of new taps

» M from M 2.00 X 0.40 to M 48.00 X 5.00
» MJ from MJ 2.00 X 0.40 to MJ 12.00 X 1.25
» MF from MF 2.00 X 0.25 to MF 48.00 X 2.00
» UNC from N 1 – 64 UNC to 4″ – 4 UNC
» UN from 5/16″ -28 UN to 2″ -6 UN
» UNS from 10 -36 UNS to 3″ -10 UNS
» UNEF from 1/4″ – 32 UNEF to 1 11/16″ – 18 UNEF
» UNF from N 0 – 80 UNF to 1 1/2″ – 12 UNF
» UNJF from 0″ -80 UNJF to 1 1/2″ -12 UNJF

» Class01 & Class51 for copper
» Class01 & Class51 for hard brass (Ms58, short chipping)
» Class01 & Class51 for soft brass (Ms63, long chipping)
» Class01 & Class51 for red brass
» Class01 & Class51 for wrought alloy of aluminium
» Class01 & Class51 for wrought alloy of magnesium
» Class01 & Class51 for thermoplastic compounds/synthetics
» Class02 & Class52 for structural steels < 1000 N/mm2
» Class02 & Class52 for case hardening steels < 1000 N/mm2
» Class02 & Class52 for heat treatable steels < 1000 N/mm2
» Class02 & Class52 for carbon tool steels
» Class02 & Class52 for Cr stainless steels, sulphured
» Class02 & Class52 for free-cutting steels
» Class02 & Class52 for cast steels < 1000 N/mm2
» Class03 & Class53 for nitride steels
» Class03 & Class53 for heat resisting steels < 1400 N/mm2
» Class03 & Class53 for Cr stainless steels, ferritic and martensitic Class03 &
» Class53 for Cr-Ni stainless steels, austenitic Class04 & Class54 for structural steels > 900 N/mm2
» Class04 & Class54 for case hardening steels > 900 N/mm2
» Class04 & Class54 for heat treatable steels > 900 N/mm2
» Class04 & Class54 for cast steels > 900 N/mm2
» Class05 & Class55 for malleable cast iron
» Class05 & Class55 for nodular graphite cast iron
» Class05 & Class55 for lamellar graphite cast iron (grey cast iron)
» Class05 & Class55 for vermicular graphite cast iron
» Class05 & Class55 for aluminium cast alloy Si 0.5% – 5 %
» Class05 & Class55 for aluminium cast alloy Si 5% – 10%
» Class05 & Class55 for aluminium cast alloy Si > 10%
» Class05 & Class55 for cast alloy of magnesium
» Class06 & Class56 for phosphor bronze
» Class06 & Class56 for alloy of titanium
» Class06 & Class56 for Ferro-TIC
» Class07 & Class57 for alloy of nickel
» Class58 for high strength structural steels fine grained

The TapPro software runs on Windows.
The screen resolution must be 1920 X 1080 or more